4 Tips To Save Money On Your Business’s Cooling Bill

Posted by on Oct 7, 2015 in Uncategorized |

Air conditioning is a must to ensure that your office is comfortable for both your clients and your employees. Even so, it can be difficult to keep a handle on the rising cost of running your commercial air conditioner all summer long. The following tips can help keep your building cool without inconveniencing your staff, your customers, or your wallet. Tip #1: Stick With A Program A programmable thermostat is one of the best ways to save money in your office. Set your AC to a higher temperature after business hours and on the weekends, then simply program it to drop to a more comfortable temperature for the hours your business is open. You will save energy by not cooling the building as much after hours. You may not want to turn of the system completely, though, since it can then take longer to cool the offices back down to a comfortable temperature. Extreme heat, such as could occur over a long weekend with no AC, can also harm electronics and computers. Tip #2: Lock and Key A programmable thermostat is only half the equation, though. You need to make sure that it stays at the pre-programmed temperature. This means protecting it from accidental (and not-so-accidental) adjustments. Thermostat lock boxes are available. These clear boxes are fitted over the thermostat so that one can still read the temperature, but they can’t access the adjustments buttons without a key. You need to use a box made for thermostats, since these are vented to allow proper air flow for temperature sensitivity. Tip #3: Automatic Pilot Open doors can suck your cool air right out of your building and suck the money right out of your pocket. Automatic doors are the simplest and most effective way to combat this issue. This completely prevents doors being propped open, and it also makes it easier for staff and customers to enter and exit the building, even if their hands are full. Don’t stop at the doors. You may also want to add sensors to your windows. With sensors, you can easily check a control panel to see if any windows have been left open, so you can arrange to close them promptly. Tip #4: Regular Service Calls You should have your HVAC system inspected regularly. At the beginning of the AC season and again at the start of the heating season are the bare minimum. Your technician can make sure that your AC is running as efficiently as possible by cleaning out fans and condenser units, replacing worn belts and hoses, and cleaning the filters. They will also check for any potential issues that are brewing so you can arrange to get them fixed...

Read More

Construction Site Dangers to Avoid When Using a Skid-Steer Loader

Posted by on Sep 23, 2015 in Uncategorized |

Skid-steer loaders are one of the most frequently seen pieces of equipment on construction sites. They are versatile and can assist in many different tasks thanks to the variety of different attachments they can be used with.  While useful and productive on the job site, though, skid-steer loaders can also be dangerous. The following are five construction site dangers caused by improper skid-steer loader use. These dangers need to be prevented to ensure worker safety: Parking on a slope A skid-steer loader is a heavy piece of equipment that can be unstable if it is parked on a very steep slope. Although a skid-steer loader has a parking brake, it is still not a good idea to park it on a slope. Always park on flat ground to avoid potential accidents.  Debris blocking controls During operation, the controls of a skid-steer loader can often become clogged and obstructed by worksite debris. This can cause enormous dangers during operation and prevent the operator from responding quickly at the controls. Before operation, it’s important to inspect the control panel and clear it of any mud, snow, ice, or other debris that have accumulated.  Leaving the controls when lift arms are up When an operator is using the lift arms, it can sometimes be tempting to leave the cab briefly to accomplish a quick task before putting the load down. However, this can put the operator at risk of being pinned under the load bucket if it fails.  The loader operator should stay seated not only when the lift arms are raised, but also at any time when the machine’s engine is running.  Carrying a load too high Keeping the skid-steer loader’s lift arms up high elevates the loader’s center of gravity. This makes it more likely for the loader to become unstable and easily knocked off balance when driving over irregular terrain.  When carrying loads, the lift arms should be up just high enough to avoid obstructions on the ground.  Improperly inflated tires A skid-steer loader typically won’t have any frame suspension. This means that the tires themselves must provide the cushioning when the loader is moving, making proper tire inflation important.  Tires need to be evenly inflated to prevent the loader from losing stability during operation. It’s also important to avoid over-inflating them. Over-inflated tires will cause a jolty ride for the operator, making it more difficult to concentrate and remain in control of the lift arms.  If you need to use a skid-steer loader for a project, look for rental equipment in your...

Read More

4 Maintenance Tips That Will Prolong The Life Of Your Roof

Posted by on Sep 2, 2015 in Uncategorized |

Getting a new roof can cost a lot of money, so making an effort to care for your existing roof is a good idea. However, you may not know what to do to prolong the life of your roof. Here are some maintenance tasks you can do on a regular basis to keep your existing roof in good condition. Look for Missing or Torn Shingles It is important to make sure that you replace any shingles that are torn, cracked or missing. When there is a problem with your shingles, the exposed part of the roof is a prime spot for water damage, especially if you leave it uncovered over time. A good time to check your shingles is after a storm, when high winds and rain can blow loose shingles off.  Be Aware of Discoloration If you see black streaks on your roof shingles or other signs of discoloration, that may be a sign that algae is growing on your roof. Algae can cause problems for the shingles themselves. Keep Trees Pruned You may like how the trees in your yard look, but it is important to keep them pruned so that they don’t hang near or on top of your roof. In a strong storm, tree branches might break off and damage your roof. Not only that, but dead leaves and twigs can fall into gutters, clogging them and enabling water to pool along the edge of your roof. That could ultimately lead to water damage. Check Flashing The metal strips that surround your chimney need to be looked at on a regular basis to ensure they are secure and in place. Sometimes, storms and high winds can cause the strips, called flashing, to become loose. If the flashing becomes loose, water might be able to seep into your home. Not only do you need to check for loose flashing, but it’s important to ensure that the metal strips themselves are in good condition. In particular, if you see any rust, consider having the flashing replaced so your roof remains protected. Now that you know some ways you can extend the life of your home’s roof, start using the tips in this article to maintain the roof’s integrity. If you want to assess the current condition of your roof or have repairs done, get in touch with a roofing contractor such as Acoma Roofing who can provide some guidance and make any needed...

Read More

Keeping Mice Out Of Your Air Conditioning Unit

Posted by on Aug 17, 2015 in Uncategorized |

If you have an air conditioner in your home, you most likely enjoy having your rooms feel comfortable when temperatures outdoors are scorching. When temperatures cool off and you pack your air conditioner away until the next warm season, it is at risk for becoming the home to mice. This can cause problems with your air conditioner the next time you go to use it, in addition to being a fire hazard if the critters happen to bite through wires within. Here are a few tips you can use to keep mice out of your air conditioning unit altogether. Do Routine Maintenance When cooler temperatures are here to stay for a while, it is best to do some routine maintenance to your air conditioner so it is ready to use when the next heat wave occurs. Clean the air conditioner, change out the filter, and unplug the unit until it is needed again. Take the time to thoroughly vacuum vents and wipe down the exterior of your air conditioner to help keep rodents away. Mice enjoy burrowing in dirtier areas, so a clean air conditioner will not be as exciting as a home. Wrap the exterior of your air conditioner using heavy-duty plastic to help keep out not only pests, but moisture as well. Take Away Attractions To keep mice out of your air conditioning unit, try taking away things that may be attracting them to stay on your property. Take up all pet food dishes so mice do not hang around trying to get a morsel to eat. Cover all fountains, birdbaths, and ponds so they do not have a water source. Keep your lawn trimmed so there are no areas of brush for mice to hide in. Use A Few Decoys Mice will stay away from areas where they feel vulnerable or where prey may be prevalent. Consider placing a few decoys around your air conditioning unit to scare mice away from the area completely. Purchase a few rubber snakes to place on the ground near your unit. Go to a hunting store and find an owl decoy to place on your deck, peeking out a window, or in a tree near to where your air conditioner is located. If you have a cat, place some cat litter from its litter box near your air conditioning unit so mice will shy away from the area when they smell the scent of a predatory...

Read More

3 Reasons Why Stud Welding Is The Best Fastening Method

Posted by on Aug 3, 2015 in Uncategorized |

Attaching studs and fasteners to metal isn’t an easy process, but there are a few methods out there that are commonly used. One of the most popular fastening methods to be used with metal is stud welding, and this option is pretty popular for a reason. If you are in an industry that requires you to attach things to metal, and if you aren’t currently using stud welding as your main method of doing so, then you are missing out on a great opportunity that could help your business. These are some of the reasons why stud welding is one of the most preferred fastening methods for metal: 1. It Only Takes One Person With many fastening methods, two or more people have to be involved to attach each additional part to each piece of metal. This can cost more in labor and can cause it to take longer to get the job done. With stud welding, however, this is not the case at all. Just one well-trained stud welder can apply pieces to metal quickly and easily, without the help of anyone else. 2. Stud Welding Works in Small Places Many fastening methods do not work well when you are working with small pieces or when you are trying to get the job done in a tight space. Stud welding, however, does not require a lot of space at all, so the job can be done just about anywhere. Plus, pieces that are both small and large work well with stud welding, so it’s a great option for jobs that cannot be done in other ways. 3. The Bond is Permanent A lot of fastening methods that are used during industrial processes are not very strong and secure. This means that pieces can fall off of metal when they shouldn’t, which can lead to an unreliable product that can earn a bad reputation among consumers. If you want to ensure that the bond between your metal and the pieces that you are attaching is as strong and durable as possible, stud welding is your best choice. Basically, stud welding should be your top choice if you value the quality and strength of your produced products. As you can see, stud welding is the best fastening method out there. If you are looking to make improvements to how your company does things, now is the time to get on board with the benefits of stud welding. Contact a company such as Northland Fastening Systems to learn...

Read More

How to Clean Your Vehicle’s Leather Seats

Posted by on Jul 20, 2015 in Uncategorized |

If you have a vehicle with leather seats, you are most likely enjoying the supple feel of the material as you drive around in comfort. Leather seating can make the interior of your vehicle look expensive and luxurious if you clean it properly, allowing it to look new for years to come. Going to a professional auto detail service to have your leather seating cared for is best, but you may be able to do the job yourself if you have the time and the right materials. Here are some tips to use when cleaning your vehicle’s leather interior. Materials You Will Need: Vacuum cleaner with attachment Air compressor Vinegar Linseed oil Spray bottle Several pieces of microfiber cloth Soft-bristled brush Leather conditioner Remove Surface Dirt Before you start deep cleaning your leather seats, remove the surface dirt. Use a vacuum cleaner attachment to remove any dust or dirt particles from your leather seats. Hold the attachment close to the seats when cleaning, but do not allow it to scrape against the surface or it may leave scratch marks. If there are pieces of dirt embedded in the cracks where the arms are attached to the seat back, use an air compressor to blow them out. Deep Cleaning Do deep cleaning on your leather seats every few months to keep them looking their best. Make a mixture of one part vinegar and two parts linseed oil and place it inside a spray bottle. This is a natural cleaner that will not damage your seat. Spray the seat and rub with a piece of microfiber cloth. To get caked-on dirt out of the leather, use a soft-bristled brush to do the job. Spray the seat and gently rub the brush in a circular motion to loosen dirt from the leather. Use a clean piece of microfiber cloth to remove any dirt that accumulates on the surface. Conditioning After you have cleaned your leather seats, you will want to condition them to give them a shine that will show off the color of the leather. Leather conditioner can be bought in an auto supply store and applied easily by spraying on the surface. Use a clean piece of microfiber cloth to buff the conditioner into the leather. Use a circular motion when buffing so all the fibers of the leather will receive conditioning equally. Allow the conditioner to dry according to the packaging directions before you get inside your vehicle. Check out http://www.deluxedetailandtint.com for more information on cleaning tips and car detail...

Read More
Page 5 of 10« First...34567...10...Last »